4CH Waterproof 5000M Long Range DC Power Output Wireless Remote Control Kit

Description

0020527
4CH  Waterproof 5000M Long Range DC Power Output Wireless  Remote
Control Kit With the external telescopic antenna
Model: 0020224
Package  Include:
1 x Receiver:
S4XW-DC06-ANT3 / S4XW-DC09-ANT3 /  S4XW-DC12-ANT3 / S4XW-DC24-ANT3
1 x Transmitter: CC-4
1 x User manual
Feature:
Application: It can be used in industry  automation, agriculture automation and home automation, such as factory, house,  farm, pasture, vehicle, ship, offshore operation, aerial vehicle, field call,  etc. It can remote control equipments on land, water and air, such as remote  control lights, sirens, locks, motors, fans, winches, blinds, linear actuators,  doors, windows, electric solenoid valves, security alarm, business signs and  various devices.
Wireless control, easy to install.
Waterproof: The receiver has waterproof case  and waterproof connector, it can be installed outdoors.
DC Power  Output: It can control DC equipment with voltage DC 6V / 9V / 12V / 24V.
With wired control terminals: You can connect  sensors, limit switches, manual switches or external devices to control the  receiver.
With the external antenna, it can have a  further working range.
Design with low-power and high-speed CMOS  technology.
You can turn on/ off the receiver with  transmitter (remote control) from any place within a reliable distance.
Wireless RF signal can pass through walls,  floors, doors or windows.
With reverse power protection and over current  protection.
Reliable control: The receiver only works with  the transmitter which use same code.
One/several transmitters can control  one/several receivers simultaneously.
You can use two or more units in the same  place.
Receiver:
Model No.: S4XW-DC06-ANT3 / S4XW-DC09-ANT3 / S4XW-DC12-ANT3 /  S4XW-DC24-ANT3
Power Supply (Operating  Voltage): DC6V (S4XW-DC06-ANT3), DC9V±1V (S4XW-DC09-ANT3), DC12V±1V  (S4XW-DC12-ANT3), DC24V±2V (S4XW-DC24-ANT3)
Output: DC6V  (S4XW-DC06-ANT3), DC9V (S4XW-DC09-ANT3), DC12V (S4XW-DC12-ANT3), DC24V  (S4XW-DC24-ANT3)
Working Frequency:  433.92MHz
Channel: 4 CH
Control Modes: Toggle, Momentary, Latched
Static Current:  ≤6mAMaximum Working Current: 10A / each channel
PCB size: 140mm x73mm x 18mm
Case size: 192mm x 100mm x 45mm
Work with Learning code transmitters.
Transmitter:
Model No.: 0021062 (CC-4)
Channel/Button: 4
Button Symbol: A, B, C, D
Operating Voltage: 9V (1  x 6F22 -9V battery, can be used for 12 months)
Working Current: 65mA  (when the transmitter is transmitting the signal), 16mA( when the transmitter is  receiving the signal).
Standby Current: 5μA
Operating Frequency:  433.92Mhz
Encoding Type: custom code
Transmitting Distance:  5000m / 16000ft (theoretically)
The distance of 5000m is a theoretical data, it shall be operated  in an open ground, no barriers, no any interference. But in the practice, it  will be hindered by trees, walls or other constructions, and will be exposed to  some interference by other signals. Therefore, the actual distance may or may  not reach 5000m.
Modulation Mode: FSK+LORA
Feedback indication: buzzing sound
Operating Temperature: -10 ° C to +70 ° C
Unit Size: 135mm x 42mm x 25mm
Weight: 90g
Uses: Household control products, agricultural control products  and industrial control products. Wireless remote control products on land, water  and air, especially in a long distance, such as farm, pasture, offshore unmanned  operation, field call, remote security alarm.
External Telescopic Antenna:
Length of external telescopic antenna: 108mm / 445mm (stretch)
With SMA connector.
If you stretches the external telescopic antenna, it can have a  further working range.
Matching Transmitters:
This receiver only works with 5000m  transmitters, such as model CC-4 (5000M), or CCW-4 (5000M, waterproof).
Working Range:
Super long range, with a transmitter (such as  CC-4) to form a complete set, the maximum working distance can reach 5000M in an  open ground.
The maximum working distance is a theoretical  data, it shall be operated in an open ground, no barriers, no any interference.  But in the practice, it will be hindered by trees, walls or other constructions,  and will be interfered by other wireless signals. Therefore, the actual distance  may not reach this maximum working distance.
Notice:
This transmitter can be used only with 5000m  series RF receivers, like model S1PUW-DC12-ANT2, S2PUW-DC12-ANT2,  S1PUW-AC220-ANT2, S2PUW-AC220-ANT2, S4PUW-DC12-ANT2, S4PUW-AC220-ANT2, ect.
Usage:
The receiver can be used to control DC 6V / 9V  / 12V / 24V equipments. If the power supply of those equipments is DC 12V, you  should choose the receiver with same DC 12V version; and if the power supply of  those equipments is DC 24V, you should choose the receiver with same DC 24V  version.
Wiring:
If you want to control a DC 12V lamp, do as  following:
1) Connect the positive pole of DC power  supply to terminal “L / +” of INPUT, and connect the negative pole of DC power  supply to terminal “N / -” of INPUT.
2) Connect the positive pole of lamp to  terminal "L / +" of OUTPUT, and connect the negative pole of lamp to terminal "N  / -" of OUTPUT.
Setting different control modes:
Setting different control modes (We have  set the receiver as Toggle control mode before delivery. If you want to use  other control modes, do as following operation):
Setting control mode Toggle: Turn on the first bit of the dip switch.
Control mode Toggle (with transmitter CC-4): Press -> On; Press again -> Off.
Press button A of the transmitter: Terminals OUT1 outputs DC power, the lamp1 is  on.
Press button A again: Terminals OUT1 stops outputting, the lamp1 is off.
…
Press button D of the transmitter: Terminals OUT4 outputs DC power, the lamp 4  is on.
Press button D again: Terminals OUT4 stops outputting, the lamp 4 is off.
Setting control mode Momentary: Turn on the first and the second bits of the dip  switch.
Control mode Momentary (with transmitter CC-4): Press and hold -> On; Release ->  Off.
Press and hold button A of the transmitter: Terminals OUT1 outputs DC power, the  lamp 1 is on.
Release button A of the transmitter: Terminals OUT1 stops outputting, the lamp 1  is off.
…
Press and hold button D of the transmitter: Terminals OUT4 outputs DC power, the  lamp 4 is on.
Release button D of the transmitter: Terminals OUT4 stops outputting, the lamp 4  is off.
Setting control mode Latched: Turn on the second bit of the dip switch.
Control mode Latched (with transmitter CC-4): Press -> On, Press another button  -> Off.
Press button A of the transmitter: Terminals OUT1 outputs DC power, the lamp 1  is on.
…
Press button D of the transmitter: Terminals OUT4 outputs DC power, the lamp 4  is on.
Other terminals stop outputting, other lamps are off.
Wired control terminals:
The receiver has  manual control terminals, you can connect external devices, sensors, or manual  switches to control the receiver.
1) Signal input:
You can connect external devices (with low level output signal) to manual  terminals “Signal –”, “Signal 1+”, “Signal 2+”, “Signal 3+” & “Signal 4+”,  then  the external device’s output signal can control the receiver.
When the external device outputs low level signal to manual terminal “Signal –”  and terminal “Signal 1+”, Terminals OUT1 outputs DC power, the lamp 1 is on.
When the external device stops to output signal, Terminals OUT1 stops  outputting, the lamp 1 is off.
When the external device outputs low level signal to manual terminal “Signal –”  and terminal “Signal 2+”, Terminals OUT2 outputs DC power, the lamp 2 is on.
When the external device stops to output signal, Terminals OUT2 stops  outputting, the lamp 2 is off.
When the external device outputs low level signal to manual terminal “Signal –”  and terminal “Signal 3+”, Terminals OUT3 outputs DC power, the lamp 3 is on.
When the external device stops to output signal, Terminals OUT3 stops  outputting, the lamp 3 is off.
When the external device outputs low level signal to manual terminal “Signal –”  and terminal “Signal 4+”, Terminals OUT4 outputs DC power, the lamp 4 is on.
When the external device stops to output signal, Terminals OUT4 stops  outputting, the lamp 4 is off.
2) The manual switches:
You can connect manual switch to terminals “Signal –”, “Signal 1+”, “Signal 2+”,  “Signal 3+” & “Signal 4+”,  and then you can use this manual switch to control  the receiver.
When connect terminal “Signal –” and terminal “Signal 1+”, Terminals OUT1  outputs DC power, the lamp 1 is on.
And when disconnect terminals “Signal –” and terminal “Signal 1+”, Terminals  OUT1 stops outputting, the lamp 1 is off.
When connect terminal “Signal –” and terminal “Signal 2+”, Terminals OUT2  outputs DC power, the lamp 2 is on.
And when disconnect terminals “Signal –” and terminal “Signal 2+”, Terminals  OUT2 stops outputting, the lamp 2 is off.
When connect terminal “Signal –” and terminal “Signal 3+”, Terminals OUT3  outputs DC power, the lamp 3 is on.
And when disconnect terminals “Signal –” and terminal “Signal 3+”, Terminals  OUT3 stops outputting, the lamp 3 is off.
When connect terminal “Signal –” and terminal “Signal 4+”, Terminals OUT4  outputs DC power, the lamp 4 is on.
And when disconnect terminals “Signal –” and terminal “Signal 4+”, Terminals  OUT4 stops outputting, the lamp 4 is off.
Setting feedback function:
If you want to have a feedback function: Turn  on the third bit of the dip switch.
When the receiver gets the signal of  transmitter, it will immediately send a return signal to the transmitter. When  the transmitter receive the feedback signal of the receiver, the transmitter  will exude a buzzing sound like “D~” which means it receive the feedback signal  successfully.
How to pair the transmitter to the receiver:
1) Press the learning button of receiver for  1- 2 seconds; signal LED on the receiver is on. The receiver enters into status  of LEARNING.
2) Press any one button on transmitter, if  signal LED flashes twice, it means learning is successful.
3) The receiver can learn several transmitters  with different codes.
Delete all transmitters:
have learned remote control to the receiver.  If you don’t want the receiver to work with the remote control, you can delete  all codes of remote controls, which are stored in the receiver.
Operation: Press and hold the button of  receiver until signal LED flashes three times. That means all stored codes have  been deleted successfully.
Shipping:
Shipping methods: Ship to Worldwide by Airmail.
Delivery time: 10~25 working days (not including week-end and holiday).
We will ship the item to your shipping address of PayPal within 1~2 working days after clearance of payment.
Please contact us immediately if you want to change your shipping address. We are not responsible for wrong address.
We will inform you via Email when shipping your items.
Guarantee:
Guaranty: One year, if the products have any quality problem, we will resend the same unit to you by free, but you need to defray the postage.